Dec 05, 2023 ご伝言

How to Replace a Ball Joint on a Chevy S-10

方法 to 交換 a ボール ジョイント オン a シボレー S-10

 

Worn ball joints on a Chevy S-10 cause alignment problems resulting in rapid uneven tire wear as well as banging noises when encountering rough surfaces. Severely worn ball joints can separate from their socket, which would result in total loss of steering. By raising each tire off the ground about 3 inches and prying up from underneath the tire, a worn ball joint can be detected by the free-play experienced when lifted.

 

ステップ 1

 

Raise and support the side of the vehicle that the service is to be performed on using a jack stand. Remove the wheel with the lug wrench. Extract the two bolts in the brake caliper using the ½-inch-drive ratchet and a socket. Remove the caliper and hang it from the spring (leave the brake hose connected).

 

STEP 2

 

Remove the cotter pin from the tie-rod end and the lower ball joint using the wire cutters. Remove the nut on the tie-rod end with a wrench. Remove the tie-rod end from the spindle with the use of the tie-rod separator tool.

 

ステップ 3

 

Move the floor jack under the lower control arm and raise it until it begins to raise the vehicle. Remove the nut on the upper ball joint and loosen the lower ball joint nut, but do not remove it. A wrench works well on both of these.

 

ステップ 4

 

セパレート 下 ボール ジョイント から 下 コントロール アーム バイ リフティング ザ アッパー コントロール アーム バイ ハンド as ハイ as it will go. フィニッシュ リムーブ ザ ロワー ボール ジョイント ナット アンド リフト ザ スピンドル オフ ザ ボール ジョイント アンド ムーブ ザ スピンドル to the リア of the ホイール ウェル。

 

ステップ 5

 

下 ボール ジョイント バイ ストレート ザ スタッド ソ ザット イット スタンド ストレート アップ アンド ヒッティング イット ハード ウィズ a ハンマー ザ ボール ジョイント ウィル フォール アウト オブ ザ ボトム オブ ザ コントロール アーム。

 

ステップ 6

 

ネジ グリース フィッティング イン 新しい ボール ジョイント 使用 a レンチ 取り付け 新しい ボール ジョイント アップ スルー 下 下 下 コントロール アーム アンド タップ it with a ハンマー 優しく to line it up so that it will be pressed in perfectly straight。

 

STEP 7

 

the ball joint in the lower control arm using the ball joint installer kit. Make sure the joint is completely in before removing the installer. Put the rubber grease seal over the ball joint stud.

 

ステップ 8

 

ライン 上 スピンドル オン 下 ボール ジョイント so that the スタッド オン the ボール ジョイント スティック スルー the hole in the スピンドル グラブ the upper control arm and push the upper ball joint stud through the upper hole in the spindle. Put the nuts on both the upper and lower ball joints and tighten. Install new cotter pins using the wire cutters. Grease the lower ball joint. Replace the rest of the parts in reverse order of removalです。

お問い合わせを送る

ホーム

電話

電子メール

引き合い